fultron12
Member
- Oct 4, 2021
- 25
This thread is ONLY for those who 1) must do partial/full suspension hanging, and 2) can only resort to using a tree.
I was a professional tree climber and trimmer for 5 years, i trimmed/felled trees away from powerlines all over Wyoming, Utah and Idaho. Just thought id give my best insights for those who feel they must use a tree for their exit strategy. This is to prevent accidents, unneeded pain and give knowledge.
When choosing your tree, the 2 most important things to know is the species, and if it is dead/dying. There are some species of trees that are incredibly soft, weak and prone to bending/snapping. But even if you choose the right species, it doesnt matter much if it is dead or has a giant crack down the middle now does it? Just like you and me, spotting a dead tree is all about inspecting the outside. The hardest part about knowing if a tree is dead/dying is if it is fall/winter and the leaves are dead and falling off.
Below is a list of things to look out for in a dead tree:
Some trees thrive in different parts of the country. An Oak is native to the east coast and grows very well there, thanks to plenty of humidity, more water, less wind, and soil composition. An aspen or cottonwood is the opposite, where they thrive more in the west. Its good to study these things if you are worried about the tree youve selected, or just have questions. All of the listed below are soft woods that are soft/weak, prone to breaking, dying, bending and snapping.
TREES TO AVOID:
This isnt a definitive list/infodump, its just the best advice i can give based on my experience and put in a way that hopefully anyone can easily grasp. If you got any questions, please feel free to ask here in the thread.
I was a professional tree climber and trimmer for 5 years, i trimmed/felled trees away from powerlines all over Wyoming, Utah and Idaho. Just thought id give my best insights for those who feel they must use a tree for their exit strategy. This is to prevent accidents, unneeded pain and give knowledge.
When choosing your tree, the 2 most important things to know is the species, and if it is dead/dying. There are some species of trees that are incredibly soft, weak and prone to bending/snapping. But even if you choose the right species, it doesnt matter much if it is dead or has a giant crack down the middle now does it? Just like you and me, spotting a dead tree is all about inspecting the outside. The hardest part about knowing if a tree is dead/dying is if it is fall/winter and the leaves are dead and falling off.
Below is a list of things to look out for in a dead tree:
- Dry, discolored and dead leaves. A tree in decay will show this at the very top or outside of its branches.
- Peeling, cracked bark. A dead tree will almost certainly have a few holes/cracks that are leaking with sap or water, or have become a home for a bird/squirrel.
- Is it hollow? Knock on the bark, and if it sounds like a low rumble instead of a light dense knock, dont use it.
- Root decay. To test this, push the tree hard in several directions, if the entire tree shuffles or leans, its a no-go.
Some trees thrive in different parts of the country. An Oak is native to the east coast and grows very well there, thanks to plenty of humidity, more water, less wind, and soil composition. An aspen or cottonwood is the opposite, where they thrive more in the west. Its good to study these things if you are worried about the tree youve selected, or just have questions. All of the listed below are soft woods that are soft/weak, prone to breaking, dying, bending and snapping.
TREES TO AVOID:
- Willows
- small Cottonwoods
- Aspens
- Lombardi Poplars
- Any Evergreen - Spruces, Pines, Firs
- Ash
- Oak
- Locust
- Elm
This isnt a definitive list/infodump, its just the best advice i can give based on my experience and put in a way that hopefully anyone can easily grasp. If you got any questions, please feel free to ask here in the thread.
Last edited: